Easy Baby Blocks
No Y Seams!
I saw this technique demonstrated in a guild meeting and decided to try it - with a little help from my friends:-)) I took pictures of each step so you could follow along. MUCH later, I discovered there was a video that explained all this. It is at the bottom of this page, along with some links to books that use this technique.
I started with
six strips cut from the width of the fabric.
(2) 3" wide lights,
(2) 2 1/2" wide darks and
(2) 2 1/2' wide mediums
(plus (4) strips of 3" wide border fabric)
sewed them together as shown in the picture and pressed to the darker color.
I cut them as shown, using the
ruler. I like this ruler because it has a 60 degree angle on top and
a 120 on the bottom. Very useful for Grandmothers Flower Garden
Blocks. When you buy this ruler, it comes with a little instruction
packet sheet, too.
cut strips on an angle, every 2 1/2". It's important to double check your angle every so often. It slides off 60 degrees after a few cuts.
(Ask me how I know...)
cut them in half through the center, matching opposite corners.
Click on the thumbnail to the left to see what I did. If your
strips aren't a true 60 degrees, you won't be able to cut corner to
corner on a 60 degree angle.
is how your boxes go together. When you lay out your top, you will
be sewing your boxes in columns. Put all your boxes together, then stand
back and look at it. Your edges will be jagged. You will be
filling in the blank area with the border fabric, so it looks like your
boxes are floating on top of the border when you get done. The
picture to the right was taken after the top was finished.
|Because I was working without a pattern, I had to guess at the edge pieces. First I measured one of the blocks (picture left), then I cut some edge pieces to match (picture right.)
The orange plastic tape you see is actually
reusable vinyl edge strips. These are guides that you place
under your ruler so your fabric can butt right up next to it. I
used it to identify the size of the piece I needed without cutting a
|Turns out I didn't think it all the way through. That was fine for the sides, but the top and bottom needed to be 120 degree blocks. To do that, I had to remove and replace the light triangles at the end of the columns. I recut them from the 3" wide border (remember, the light was a 3" wide strip) and replaced the end triangles with the border triangles. The end strips are shown to the right, but before you copy this picture, read my note at the bottom of the page.
That's Best Press in the upper left hand corner of the picture. Trust me, you will need some sort of spray starch before your are all done. Those edges stretch!
|Lay these out in columns, then sew your columns together. Notice the odd angle that happens when you sew your pieces together. When pressing, always press the light seams over the dark block and the medium seams over both light and dark. In other words, press the seams of the dark IN and the seams of the medium OUT. This will make a difference when you sew your columns together.|
|Sew your columns together. Because of the way you pressed your seams, the intersections should just nestle. If you have a problem, try placing a pin at the point of the triangle and matching the same position on the other column. Or you can just ease to fit. If you click on the thumbnail of my quilt top, you will see I did that in several places. (It'll quilt out:-))
| It looked like this before I pressed it. I laid the ruler on the top, putting the 1/4" line along the bottom of the boxes.
|If you click on the thumbnail, you will notice I wasn't very exact! I didn't catch that until I saw the picture.|
|I pressed the heck out of this top, using lots of
Best Press. I pressed the columns in opposite directions. I measured through the center in several places and discovered it averaged about 34 1/2" wide. I think the variance was caused by the fact more than one person worked on this top on more than one machine. Plus I wasn't as careful as I should have been. I really was just trying to teach myself the technique.
|I cut two 3" wide border strips 34 1/2" long and sewed them to both sides, easing to fit. Then I repeated the process with the top and bottom. Matching border strips like this is a tried-and-true method of making your quilt top square. My top ended up 34 1/2" x 40".
I discarded several miss-cuts along the way, so yours may end up larger.
|Looking closely at the finished top at the top of this page, I see that first row doesn't make a lot of sense. I should have added another half block. The next time I make this, I will plan a little better. If you decide to try this, send me a picture, please. I would love to see how you did.|
Have another tip to offer? Send it me, and I will add it here.
More tips, tutorials and techniques are available at http://phoebemoon.com/tutorials/
Copyright Phoebemoon.com. All rights reserved.